Wilton 99175 6 Amp 4-Inch/8-Inch 4/5 Horsepower Benchtop Belt/Disc Sander

Wilton 99175 6 Amp 4-Inch/8-Inch 4/5 Horsepower Benchtop Belt/Disc Sander | This is the one to buy.

tools & hardware:

Wilton 99175 6 Amp...

	Wilton 99175 6 Amp 4-Inch/8-Inch 4/5 Horsepower Benchtop Belt/Disc Sander WMH Tool Group WMH Tool Group average customer review:based on 16 reviews view larger image
	for more information click here

highly recommended

Wilton Benchtop Belt / Disc Sander

ABsolutely great machine for the price. Nice and heavy, accurate table angles, great dust diversion, easy to "fine tune" pieces even with heavy grit belt. Received the piece within a few days of ordering, had it assembled and ready to go in about 45 min's. Practiced on a couple pieces of scrap pine, and 10 minutes later, first project was under way. Needed to cut a perfectly round 4" disc. Started with a rough cut using band saw, but got it perfect by trimming down to the pencil line. Great product, great deal, and I'm happy. After all, that's all that really matters, right?? :-)
G Schaeffer

for more information click here

This is the one to buy.

I do small woodworking projects, frames, small tables, crosses and various knick-knacks. For the price range and size, this is it. I had a Rikon, it never worked well - the tracking was unstable and it did not handle much material. I gave it away and bought this one based on customer recommendations I read here. In my opinion - and i use the heck out of this thing - it is as much as you will find for the price and size.

Pretty impressed so far

Bought this to replace a Delta that I bought in March 2006. The Delta's plastic drive wheel stripped gears in the first month and I repaired it. For about the last 3 months I've had to tinker with it before it would start. I put it in the dump and bought this Wilton. The FIRST thing I did was open the power transfer box and check the drive wheels. They are metal, cheap metal, but metal and the look substantial enough for the 4/5 horsepower motor. First use it worked pretty good - runs steady, tracks perfectly, doesn't bog. It is easy to set up and quiet when it is running. I'd recommend this to a hobby woodworker. Light to moderate use, it will do just fine for you.

for more information click here

Good small stationary sanding station that likes dust

I have used this router for about 5 months, on and off, here and there in that time frame. I have no complaints as it allows me to sand any work piece without manually sanding it by hand or compromise safety by breaking out the orbital sander for small pieces of wood.

Assembly is minimal as one would need to install the sanding disc table, the dust guard for the belt and the fence. After that it is ready to use as the sanding belt and disc are already installed. Both are 60 grit.

The provided miter gauge is reasonable but for finer things, it may need to be adjusted. However, the tilt adjustment for the disc table and the fence seem to be good for 90 degrees. I have yet to try it with other angles but I am sure that for any first time use that calibration is needed to double check the manufacturer's gauges. I have yet to use the sander in all the adjustment angles besides the included miter.

Operation is a slow to full speed start which I like. The power switch is big and right there so you can quickly turn it off and on. The instruction manual provides some details on bench mounting which is a must (though for awhile, I used it without bolting it down to a surface and it was steady). Because of this, it maybe justified by the manufacture to only have TWO mounting holes for your bolts.

Build wise, the housing is mostly casted metal and the belt apparatus sits on top of the casingand the disc to the side. The disc table doesn't feel flimsy once installed and once set to the proper angle it stays solid. The belt back fence takes a bit to adjust and install and does not have that similar feeling of solidness but it gets the job done. The guard for the belt sander doesn't do much for collecting and gathering dust so it can go out of the dust port. The belt stop right before the dust guard while solid metal doesn't feel solid enough to be used as a guide. Just meerly a simple stop.

Have yet to change out the sanding disc but belt adjustment is pretty intuitive. You do have to check to see if the belt drifts over time though and that can be done easily.

The only thing about this 8" disc sander and the 4" belt is that the sanding disc is not something that your Lowes or Home Depot would carry. Either find a Harbor Freight Tools store to get your discs there or order online.

Now for dust... The dust collection system for the tool is only good for the belt. It may provide collection with the disc but you would need a powerful suction system to take care of that. Don't expect your mobile shop vac purchased cheaply from your big name hardware store to handle the dust collection, you will need something better and even then dust still builds up here and there amongst the tool.

The base of the unit has a removable plate and you can access the innards of the solid metal casing. sawdust will naturally build up there overtime and that volume of area also is shared with some wires that are exposed to the inside area that the sawdust (if not cleared out) shares space with. It is something noted for long term usage to clean out this sucker once in awhile.

I am satisfied with this tool but it is very limited because it is a small stationary sander. Don't expect to fit big pieces of wood to sand accurately (you need to find other means to do this). Small pieces of work are fine. It is a tool that for my purposes is needed on occasion but now that I have a miter saw and a router, accurately getting my rough cuts to the exact edge I want is not a problem anymore and this tool stands by as an auxilary tool. I think I would have gotten along fine without the tool though.

for more information click here

reviews: page 1, 2, 3, 4

products you might be interested in