All in One Clamp U99 99" Ultra All In One Clamp

All in One Clamp U99 99" Ultra All In One Clamp | can't cut wood without it

tools & hardware:

All in One Clamp U...

	All in One Clamp U99 99" Ultra All In One Clamp E. Emerson Tool Co E. Emerson Tool Co average customer review:based on 12 reviews view larger image
	for more information click here

highly recommended

The Ultra Clamp is exactly that, an Ultra Clamp. An extra wide, long rigid straight edge. One solid piece of aluminum. With the same edge profile as the Single Series and the Twin Series, the Ultra accepts all of our accessories. It can be quite difficult to manage sheet goods at times. With the use of a 99" Ultra Clamp, an accessory Wide Jaw and Story Stick length-cuts are made easily without using your table saw.

Great product

I am a general contractor and do many of the smaller jobs as well. I have owned a competitor's 48" brand for years and love using it on the bottom of doors for a straight cut. I had been looking for an 8'version so I could use it to rip down the width of doors plus plywood accurately. When I ran across this, I was excited and purchased it immediately. I have used it on several applications and I can tell you it is worth it's weight in gold. I must say that there is a slight glitch in it's use but once you understand it, it is not a problem. The slight glitch is that sometimes you have to "reset" the locking mechanism with your finger to re-establish the locking ability. Once you figure this out, it's not a problem. I mention this for two reasons, first to save you the frustration you will feel when you think it's not holding properly. Perhaps this is a design flaw because my name brand 48" does not have this issue. Secondly, I noticed that the only "1" star rating so far on this product mentions this complaint. Even with the need to snap the locking pin in place from time to time, I am so pleased with what this guide does for me. It is well worth the cost because it does get the job done. I just wish they would offer a case to hold it for storage. Hope this helps....

for more information click here

can't cut wood without it

This clamp is the best tool I ever owned. Fantastic tool makes your cutting work so precise and accurate. My God where was I before buying this clamp. I can't add more go ahead and grab one if you need to cut sheets of 8 feet or smaller you wont regret it. By the way this clamp is NOT as heavy as it looks.

All In One Clamp 99

Well worth the money if you cutting full sheets of plywood...saved me a lot of re-sawing...great product!

Works Well, But...

The aluminum had some slight dings from shipping. Not serious, but I needed to scrape them smooth.

The adjustable clamp is oddly not intuitive and did not seem to work the first time I tried the product. But I flipped the rail over and it was obvious how to set or release the clamp. Once I had it snugged against the far end of a sheet of 4 by 8 birch ply, the locking (fixed) end clamp did the job.

Works and works well and the 99" length makes the last bit of a cut easier to keep straight.

I also bought the option saw base-- can't use it. It is too small for many of the newer pro-style saws, has the holes in useless places and the worst instructions I've seen in quite awhile. They show the saw installed for use with motor side away from the part the rides the rail: that is as if the saw guide was to be used to the right of the cut. The very tiny photo shows the plate installed so that the guide rail is to the left of the cut. In either case the right side of my saw base would be almost at the edge of the plastic base, leaving no room for screws. The instructions tell you that if you have to custom drill holes that they should be counter sunk on the bottom of the saw base, but the ones that are pre-drilled are counter sunk on the top side. Who knows.

Anyway the reviewers who complain about the clamps probably did not take the extra time to figure out how to "lock" the adjustable clamp before tightening the fixed clamp. Good product --but no instructions are by definition not good instructions.

for more information click here

reviews: page 1, 2, 3

products you might be interested in